>
Hyundai Equus: Climate Seat Unit Repair procedures
| Removal |
| 1. |
Disconnect the negative (-) battery terminal. |
| 2. |
Remove the front seat.
(Refer to Body - "Front Seat Assembly") |
| 3. |
Remove the front seat cushion cover.
(Refer to Body - "Front Seat Cushion Cover") |
| 4. |
Remove the blower fan (A) after removing the fixed clip (B) and screws.
|
| 5. |
Remove the front seat back board.
(Refer to Body - "Front Seat Back Cover") |
| 6. |
Remove the TED (A) from the seat back and then loosen the screws.
|
| 7. |
Disconnect the TED connector and then remove the duct. |
| 1. |
Disconnect the negative (-) battery terminal. |
| 2. |
Remove the front seat.
(Refer to Body - "Front Seat Assembly") |
| 3. |
Remove the climate control system seat unit (A) after disconnecting the connectors and loosening the screws.
|
| 1. |
Disconnect the negative (-) battery terminal. |
| 2. |
Remove the rear seat.
(Refer to Body - "Rear Seat Assembly") |
| 3. |
Remove the rear seat cushion.
(Refer to Body - "Rear Seat Cushion Cover") |
| 4. |
Remove the blower fan and the TED (B) after loosening the screws from the seat frame.
|
| 5. |
Remove the rear seat back cover.
(Refer to Body - "Rear Seat Back Cover") |
| 6. |
Disconnect the connectors.
|
| 7. |
Remove the blower fan (A) and the TED (B) after loosening the screws.
|
| 1. |
Disconnect the negative (-) battery terminal. |
| 2. |
Remove the rear seat.
(Refer to Body - "Rear Seat Assembly") |
| 3. |
Remove the climate control system seat unit (A) after disconnecting the connectors and loosening the screws.
|
| Installation |
| 1. |
Connect the connector and then install the TED and climate control system duct on the side of the seat back. |
| 2. |
Install the front seat back board. |
| 3. |
Install the blower fan by connecting it to the connector and fixed clip under the front seat cushion. |
| 4. |
Install the TED on the seat cushion. |
| 5. |
Install the front seat cushion. |
| 6. |
Install the front seat. |
| 7. |
Connect the negative (-) battery terminal. |
| 1. |
Install the climate control system seat unit after connecting the connectors. |
| 2. |
Install the front seat. |
| 3. |
Connect the negative (-) battery terminal. |
| 1. |
Install the blower fan and the TED on the side of rear seat back. |
| 2. |
Install the rear seat back. |
| 3. |
Install the blower fan and the TED under the rear seat cushion. |
| 4. |
Install the rear seat cushion, the duct and bracket. |
| 5. |
Install the rear seat. |
| 6. |
Connect the negative (-) battery terminal. |
| 1. |
Install the climate control system seat unit after connecting the connectors. |
| 2. |
Install the rear seat. |
| 3. |
Connect the negative (-) battery terminal. |
Climate Seat Unit Description and Operation
Lumbar Support Unit Components and Components LocationHow does the air bag system operate
Air bags are activated (able to inflate if necessary) only when the Engine
Start/Stop Button is turned to the ON or START position.
Air bags inflate in the event of a severe frontal or side co ...
Driving in flooded areas
Avoid driving through flooded areas unless you are sure the water is no higher
than the bottom of the wheel hub. Drive through any water slowly.
Allow adequate stopping distance because brake perfo ...
Description and Operation
Description
Adaptive Front-lighting System (AFLS)
AFLS(Adaptive Front-lighting System)is a headlamp
orientation control system that takes into account both steering angle
and vehicle speed to ...