>
Hyundai Equus Manuals

Hyundai Equus: Front Hub / Knuckle / Tone Wheel Repair procedures - Front Axle Assembly - Driveshaft and axle - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Front Hub / Knuckle / Tone Wheel Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub / Knuckle / Tone Wheel Repair procedures

Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub .

   
Be careful not to damage to the hub bolts when removing the front wheel and tire .
3.
Remove the brake caliper mounting bolts, and then hold the brake caliper assembly (A) with wire.
Tightening torque :
80.0 ~ 100.0 Nm (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

[Air Suspension Type]

4.
Loosen the brake disc mount screw then remove the brake disc (A).
Tightening torque :
4.9 ~ 5.8 Nm(0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

5.
Disconnect the wheel speed sensor (A) from knuckle.

6.
Remove the tie rod end ball joint from the knuckle.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Disconnect the ball joint (D) from knuckle (C) using the special tool (09568-4A000).
Tightening torque :
88.3 ~ 107.9 Nm (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.5 lb-ft)

   
Apply a few drops of oil to the special tool. (Boot contact part)
7.
Loosen the tension arm mount nut (A), and then remove the tension arm (B).
(1)
Remove the split pin (C).
(2)
Remove the castle nut (D).
(3)
Disconnect the ball joint (B) from knuckle (A) using the special tool. (09568-4A000)
Tightening torque :
137.3 ~ 156.9 Nm (14.0 ~ 16.0 kgf.m, 101.2~115.7 lb-ft)

   
Be careful not to damage the boot and rotor teeth.
8.
Loosen the lateral mount nut.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Disconnect the ball joint (C) from knuckle (D) using the special tool.(09568-4A000)
Tightening torque :
90.0 ~ 110.0 Nm (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

9.
Remove the hub and knucke assembly (C).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Disconnect the ball joint from knuckle using the special tool (09568-4A000).
Tightening torque :
35.0 ~ 45.0 Nm (3.5 ~ 4.5 kgf.m, 25.3 ~ 32.5 lb-ft)

10.
Remove the hub assembly (B) from knuckle assembly.
Tightening torque :
80.0 ~ 100.0 Nm (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

11.
Loosen the dust cover mount bolts and then remove the dust cover (B) from knuckle (A).
Tightening torque :
7.0 ~ 11.0 Nm (0.7 ~ 1.1 kgf.m, 5.0 ~ 7.9 lb-ft)

12.
Installation is the reverse order of removal.
Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the knuckle for cracks.
4.
Check the bearing for cracks or damage.
    Front Hub / Knuckle / Tone Wheel Components and Components Location
    Component location 1. Front knuckle assembly2. Hub assembly3. Dust cover4. Brake disc ...

    Rear Axle Assembly
    ...

    See also:

    Description and Operation
    Description The hydraulic system consists of oil, an oil filter, an oil pump, and a valve body (valves and solenoid valves). The oil pump is powered by the engine. ATF passes through the oil filt ...

    Vehicle break-in process
    No special break-in period is needed. By following a few simple precautions for the first 600 miles (1,000 km) you may add to the performance, economy and life of your vehicle. Do not race the ...

    Rear Seat Assembly Repair procedures
    Replacement [Rear Seat Cushion Assembly] 1. Pull it up and remove the rear seat cushion assembly (A). 2. Install in the reverse order of removal.     • Make sure the ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com