>

Hyundai Equus: Jump starting - Emergency starting - What to do in an emergency - Hyundai Equus 2009-2024 Owners ManualHyundai Equus: Jump starting

Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or battery, follow the jump starting procedures. If in doubt, we strongly recommend that you have a competent technician or towing service jump start your vehicle.

CAUTION

Use only a 12-volt jumper system. You can damage a 12-volt starting motor, ignition system, and other electrical parts beyond repair by use of a 24- volt power supply (either two 12-volt batteries in series or a 24-volt motor generator set).

WARNING - Battery

Never attempt to check the electrolyte level of the battery as this may cause the battery to rupture or explode causing serious injury.

WARNING - Battery

  • Keep all flames or sparks away from the battery. The battery produces hydrogen gas which may explode if exposed to flame or sparks. If these instructions are not followed exactly, serious personal injury and damage to the vehicle may occur! If you are not sure how to follow this procedure, seek qualified assistance. Automobile batteries contain sulfuric acid. This is poisonous and highly corrosive. When jump starting, wear protective glasses and be careful not to get acid on yourself, your clothing or on the car.
  • Do not attempt to jump start the vehicle if the discharged battery is frozen or if the electrolyte level is low; the battery may rupture or explode.

Jump starting procedure

✽ NOTICE

Your vehicle has a battery in the trunk compartment, but when you jump start your vehicle, use the jumper terminal in the engine compartment.

1.Make sure the booster battery is 12-volt and that its negative terminal is grounded.

2.If the booster battery is in another vehicle, do not allow the vehicles to touch.

3.Turn off all unnecessary electrical loads.

4.Connect the jumper cables in the exact sequence shown in the illustration. First connect one end of a jumper cable to the positive terminal of the jumper terminal (1), then connect the other end to the positive terminal on the booster battery (2). Proceed to connect one end of the other jumper cable to the negative terminal of the booster battery (3), then the other end to the negative terminal of the jumper terminal (4).

Do not connect it to or near any part that moves when the engine is cranked.

Do not allow the jumper cables to contact anything except the correct battery terminals or the correct ground. Do not lean over the battery when making connections.

CAUTION - Battery cables

If you jump start the discharged battery in the trunk compartment, do not connect the jumper cable from the negative terminal of the booster battery to the negative terminal of the discharged battery. This can cause the discharged battery to overheat and crack, releasing battery acid. Connect the jumper cable from the negative terminal of the booster battery to a solid, stationary or metallic point away from the discharged battery.

5.Start the engine of the vehicle with the booster battery and let it run at 2,000 rpm, then start the engine of the vehicle with the discharged battery.

6.Let the discharged battery run for at least 20 minutes either by engine idling or by driving before you turn it off else the discharged battery may not be recharged enough to restart the car.

If the cause of your battery discharging is not apparent, you should have your vehicle checked by an authorized EQUUS dealer.

    Emergency starting
    Connect cables in numerical order and disconnect in reverse order. ✽ NOTICE Your vehicle has a battery in the trunk compartment, but when you jump start your vehicle, use the jumper termi ...

    Push-starting
    Vehicles equipped with automatic transmission cannot be push-started. Follow the directions in this section for jump-starting. ...

    See also:

    Front Hub / Knuckle / Tone Wheel Repair procedures
    Replacement 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire (A) from front hub .     Be ca ...

    27 Brake Control Solenoid Valve Schematic Diagrams
    Circuit Diagram ...

    Components and Components Location
    Components 1. Backing plate2. Operating lever3. Upper spring4. Lower spring5. Adjuster6. Shoe hold down spring7. Shoe hold down pin8. Parking brake shoe9. Cup washer ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com