>
Hyundai Equus Manuals

Hyundai Equus: TPMS Receiver Description and Operation - Tire Pressure Monitoring System - Suspension System - Hyundai Equus VI 2009-2025 Service ManualHyundai Equus: TPMS Receiver Description and Operation

Second generation VI (2009–2025) / Hyundai Equus VI 2009-2025 Service Manual / Suspension System / Tire Pressure Monitoring System / TPMS Receiver Description and Operation

Description

1.
Mode
(1)
Virgin State
A.
The receiver as a sole part is shipped in this state. Replacement parts should therefore arrive in this state.
B.
In this state, there is no Auto-Location, no sensor wake-up, no sensor monitoring and no DTC monitoring..
C.
The state indicates that platform specific parameters must be written to the receiver and that sensors are un-learned.
(2)
Normal State
A.
In order for tire inflation state and DTC monitoring to occur, the receiver must be in this state.
B.
In this state, automatic sensor location / learning is enabled.
2.
Overview
A.
Receives RF data from sensor.
B.
Uses sensor data to decide whether to turn on TREAD Lamp.
C.
Learn TPM sensor for under inflation monitoring automatically.
D.
Uses sensor information, Auto-learn status, short/open circuit output status, vehicle battery level, internal receiver states to determine if there is a system or a vehicle fault.
Operation
1.
General Function
A.
Auto-locate/learn takes place only once per Ignition cycle.
B.
On successful completion, 4 road wheel sensor ID's, together with their respective road wheel positions are latched into memory for monitoring.
C.
Until Auto-learn completes, previously learned sensors (together with their respective locations) are monitored for under inflation / leak warnings.
2.
General Conditions to Learn New Sensors:
A.
Receiver must Auto-Locate 4 road sensors.
B.
Auto-location / learning only functions when speed is more than 25 kph (approx. 15 mph).
C.
Receiver must determine that it is confident that sensor is not temporary:
1)
Uses vehicle speed.
2)
Uses confidence reduction of previously learned sensors.
D.
Typical time at driving over 25 kph (15.5mph) to learn a new sensor is up to 10 minutes.
3.
General Conditions to Un-Learn a sensor that is removed:
A.
It takes less than 10 minutes at 20~25kph. (15 ~ 15.5mph)
B.
Confidence reduction is dependant on vehicle speed and the number of sensors known to the receiver.
    TPMS Sensor Repair procedures
    Removal Tire Removal 1. Deflate tire & remove balance weights.     • The tire bead should be broken approx. 90° from the valve side of the wheel. The bead breaker sho ...

    TPMS Receiver Repair procedures
    Replacement     When the receiver first arrives for replacement: 1) It will be in Virgin State. 2) It will not have any sensor ID's memorized.     It ...

    See also:

    Heater Unit Components and Components Location
    Component Location Components 1. Heater Case (Left)2. Vent Door (Left)3. Temperature Door (Left)4. Floor Door (Left)5. Console Temperature Control Actuator (A) 6. Console Temperature Lever7. Con ...

    Driving your vehicle
    WARNING - ENGINE EXHAUST CAN BE DANGEROUS! Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the windows immediately. Do not inh ...

    Filler-Neck Assembly Repair procedures
    Removal 1. Disconnect the fuel filler hose (A) and the leveling hose (B). 2. Disconnect the vapor hose quick-connector (A) after removing the trunk luggage trim. 3. Remove the rear-LH whee ...

    Categories

    Hyundai Equus Manuals

    © 2011-2025 Copyright www.heqmanual.com