Hyundai Equus: Compass Mirror Description and Operation
Second generation VI (2009–2025) / Hyundai Equus VI 2009-2025 Service Manual / Body Electrical System / Electro chromic Inside Rear View Mirror / Compass Mirror Description and Operation
Second generation VI (2009–2025) / Hyundai Equus VI 2009-2025 Service Manual / Body Electrical System / Electro chromic Inside Rear View Mirror / Compass Mirror Description and Operation
| Description |
The compass feature is designed to be integrated into an electro chromic interior rearview mirror.
The mirror assembly shall display a compass heading.
The compass mirror then take the sensor information to
determine static field strengths and rotating field information to
determine an accurate compass heading.
Specification
| Item | Standard value |
| Rate voltage | DC 12V |
| Operating voltage range | DC9 ~ 16V |
| Operating temperature range | -30 ~ +65°C (-22 ~ 149°F) |
| Direction display | 8 |
| Renewal time | 2 sec. |
Switch Point Accuracy
The compass module shall, while compensating for the vehicle
magnetic fields, until the Earth's varying magnetic fields to determine
direction.
[Switch points]
| Switch point | Heading ± 10° |
| N - NE | 22.5 |
| NE - E | 67.5 |
| E - SE | 112.5 |
| SE - S | 157.5 |
| S - SW | 202.5 |
| SW - W | 247.5 |
| W - NW | 292.5 |
| NW - N | 337.5 |
There should be hysteresis at each switch point.
Switch points between the 8 cardinal directions, these switch points are ± 10° |
Compass display interval
Compass display should be updated at every two seconds.
| Function |
The compass can be turned ON and OFF and will remember the
last state when the ignition is cycled. To turn the display feature
ON/OFF :
| 1. |
Press and release the feature control button (A) to turn the display feature OFF. |
| 2. |
Press and release the feature control button (A) again to turn the display back ON.
Additional options can be set with press and hold sequences of the feature control button (A) and are detailed below.
There is a difference between magnetic north and true north.
The compass in the mirror can compensate for this difference when it
knows the magnetic zone in which it is operating. This is set either by
the dealer or by the user. |
Repair procedures
Inspection
Check it by the procedure below to see if the function of the ECM is normal.
1.
Turn the ignition key to the "ON" position.
2.
Cover the front looking sensor to stop functioning.
...
Compass Mirror Repair procedures
Adjustment
Calibration procedure
If the display read "C", calibrate the compass.
1.
Driving the vehicle in a circle at less than 8km/h 3 times or until the compass heading appears.
2.
Drivin ...
See also:
Pre-active Seat Belt (PSB) Components and Components Location
Components
Main Function
1.
Full Retraction
Maintains a more safe posture by strongly rewinding the seat belt right before a crash.
[Operation Condition]
A.
When a frontal crash is detected b ...
Receiver-Drier Repair procedures
Replacement
1.
Remove the condenser.
2.
Remove the cap (B) on the bottom of the condenser with a L wrench (A).
Tightening torque :
2.7 ~ 3.1 N.m (0.28 ~ 0.32 kgf.m, 2.0 ~ 2.3 lb-ft)
...
In-car Sensor Description and Operation
Description
An in-car air temperature sensor is located in the heater control.
The sensor contains a thermistor which measures the
temperature of the cabin. The signal determined by the resistan ...
Categories
Hyundai Equus Manuals
© 2011-2025 Copyright www.heqmanual.com