>
Hyundai Equus Manuals

Hyundai Equus: Water pump Repair procedures - Cooling System - Engine Mechanical System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Water pump Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Engine Mechanical System / Cooling System / Water pump Repair procedures

Removal and Installation
Water Pump
1.
Disconnect the negative terminal (A) from the battery.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

2.
Remove the air duct, air intake hose and the air cleaner assembly.
(Refer to Engine and transaxle assembly in this group)
3.
Loosen the drain plug (A) and drain the engine coolant. Remove the radiator cap (B) to speed draining.
   
Never remove the radiator cap when the engine is hot. Serious scalding could be caused by hot fluid under high pressure escaping from the radiator.

4.
Disconnect the radiator upper hose (A) and lower hose (B).

5.
Turn the tensioner (B) clockwise and loosen, then remove the drive belt (A).

6.
Remove the water pump pulley (A).
Tightening torque :
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)

7.
Remove the water pump (A).
Tightening torque :
19.6 ~ 24.5 N.m (2.0 ~ 2.5 kgf.m, 14.5 ~ 18.1 lb-ft)

   
Always use a new gasket.
8.
Installation is reverse order of removal.
Water pipe
1.
Remove the intake manifold module.
(Refer to intake and exhaust system in this group)
2.
Remove the injector & rail assembly.
(Refer to FL group)
3.
Remove the water outlet pipe (A) and the water inlet pipe (B).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
   
•
Use new O-rings when reassembling.
•
Never apply sort of oil on O-ring and O-ring groove of pipe end.
•
O-ring must be free from scratching damage.
   
•
Make clean the contact face before assembly.
•
Insert pipe after to be wetting O-ring or inside of attaching hole by water or antifreeze.

   
Remove the drain plug (A) and drain the engine coolant.
Tightening torque :
96.1 ~ 100.0 N.m (9.8 ~ 10.2 kgf.m, 7.2 ~ 8.7 lb-ft)

4.
Installation is reverse order of removal.
    Water pump Components and Components Location
    Components 1. Drive belt2. Drive belt tensioner3. Drive belt idler4. Water pump pulley5. Water pump6. Water pump gasket ...

    Water pump Troubleshooting
    Troubleshooting Water Pump SymptomsPossible CausesRemedyCoolant leakage • From the bleed hole of the water pump Visually check • Check leaks after about ten-minute warming up. • ...

    See also:

    Electronic Hydraulic Power Steering (EHPS)
    This system uses an electromotor to assist you with steering the vehicle. If the engine is turned off or if the EHPS becomes inoperative, you may still steer the vehicle, but it will require increa ...

    27 Brake Control Solenoid Valve Specifications
    Specifications Direct control VFS[27/B] x Control type : Normal low type Control Pressure kpa (kgf/cmx, psi)0~1569.06 (0~16,0~227.57)Current value(mA)0~1100 Internal resistance ...

    Mode Control Actuator Description and Operation
    Description The mode control actuator is located at the heater unit. It adjusts the position of the mode door by operating the mode control actuator based on the signal of the A/C control unit. ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com