>
Hyundai Equus Manuals

Hyundai Equus: Compressor Repair procedures - Air Suspension System - Suspension System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Compressor Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Suspension System / Air Suspension System / Compressor Repair procedures

Removal
   
•
This system combines a sensor and electronic parts with mechanical components, so be careful not to subject the system to strong impacts.
•
If any pins are visible inside the electric signaling connector, do not expose it to water.
•
A plug protects the air inlet of the reservoir tank from dust or other particles. Do not remove the plug except when assembling or disassembling the reservoir tank.
•
DO NOT hold any parts by their electric wires while moving them, as the weight of the part may damage the wire or connection during transport.
•
Do not pile components on top of each other.
•
Do not apply power to operate the compressor directly (may cause malfunctions/overheating).
•
Be careful not to break any circuits by twisting or bending the cables.
•
DO NOT drop any parts.
•
Check the color of each air hose before connecting it. After connecting a hose, pull it to ensure that the connection holds firm.
•
The air connection section of the air hose includes a dust cover to prevent the introduction of foreign substances. DO NOT remove this cap for any process besides connecting the hose.
•
When installing an air hose, be careful not to kink the hose.
•
DO NOT reuse the air hose connector connected to an air hose assembly after it has been disassembled.
•
The markings on both ends of the air hose distinguishes the assembly, so be careful not to peel it off.
1.
Removal the front bumper.
(Refer to Body - "Front bumper")
2.
Removal the left head amp.
(Refer to Body Electrical System - "Head lamp leveling device")
3.
Removal the EHPS motor.
(Refer to Steering System - "Power steering motor")
4.
Disconnect the connector (A) & air hose (B).

   
•
Work with time until air is discharged.
•
Separate with push the air tube connected to center portion.
5.
Remove the bracket bolt.

6.
Disconnect the solenoid valve (A) from the compressor by loosening the bolt.

7.
Installation is the reverse of removal.
   
•
Take care not to drop.
•
Confirm the tube color in installation process.
•
Confirm that whether the tube is escaped a not by puling it.
•
Be careful not to disconnection of cable by its twist or excessive bending.
•
Do not remove cap except assemble.
•
Take care not to twisted.
•
If disassemble the air tube connector, do not reuse it.
•
Air tube marking takes care not to be came off.
    Compressor Schematic Diagrams
    Circuit diagram 1. Air compressor connector [Motor power connector (A)][Exhaust valve connector (B)][Temperature sensor connector (C)] 2. Air compressor terminal function [Motor power] ...

    Solenoid Valve Components and Components Location
    Components 1. Connected to air tube2. Bracket3. Connector ...

    See also:

    Components and Components Location
    Components Location 1. Smart Junction Box (SJB)2 . Body Control Module (BCM)3 . Smart Key Unit (SMK)4 . Driver Door Module (DDM)5 . Assis Door Module (ADM)6 . Cluster (CLU)7 . Around View Monitor ...

    Height Adjust Repair procedures
    Replacement 1. Remove the front seat belt upper anchor. (Refer to Front Seat Belt - "Front Seat Belt Pretensioner") 2. After loosening the mounting bolts, then remove the height adjustor (A) ...

    Description and Operation
    Description The ECM (Electro Chromic inside rear view Mirror) is for dimming the reflecting light from a vehicle behind at night, in order the user not to be dazzled by the light. The front loo ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com