>
Description |
1. |
When IGN1 signal is ON. |
2. |
When BLIND SW is ON. |
3. |
When “P “ and “R” positons are all OFF. |
4. |
When Speed spec is satisfied. |
5. |
Vehicle speed Spec.
|
1. |
When IGN1 signal is ON. |
2. |
When R position signal is ON and P position signal is OFF. |
- |
Backward drive route’s guide lines display by steering wheel angle. |
- |
Backward neutrality route’s guide lines display by steering wheel angle. |
1. |
0.5m from the rear bumper |
2. |
1.0m from the rear bumper |
3. |
3.0m from the rear bumper |
4. |
The route of wheel of a driver side
|
5. |
The route of wheel of assist side
|
6. |
Fixed parking guide line.
|
1. |
G1
The user moves the car to align proper position of the target parking area. After select garage parking.
Turn the wheel to the target parking area like below picture and the step is changed to G2 after 2sec when speed is generated.
The view mode is changed to Rear View Mode when the Back menu is selected in G1. |
2. |
G2
Hold the arranged wheel angle in G1 and move backward slowly to front of parking area.
The vehicle is paralleled in the parking area by the user.
The step is finished when the wheel angle is moved to neutral position.
The View mode is changed to G1 when the Back menu is selected in G2. |
1. |
P1
After select parallel parking, the user moves the car to align proper position of the target parking area.
The user can select the menu of parallel parking in rear view
mode and next step is P1 for parallel parking until the user is parking
to proper target parking area.
The PGS system supports two kind of guide line these are
related the target parking area and guide line of anti-collision. The
design of the line can be altered by the conference.
The guide line is displayed to selected direction when the wheel is aligned to target parking area.
Hold the stop status until the guide lines(by wheel angle)
are aligned with the blue lines(parking area’s guide lines). When the
repeated blinking of guide line is stopped, the P1 will be changed to
next step(P2) after generated speed.
The View mode is changed to Rear View Mode when the Back menu is selected in P1. |
2. |
P2
The P2 is a step which vehicle is moved to backward to properly parking area.
Hold the wheel controlled in the P1 step and move backward until the green lines() aligned to inside of target parking area().
The View mode is changed to P1 when the Back menu is selected in P2. |
3. |
P3
Hold the arranged wheel angle in P2 and move backward slowly to front of parking area.
The vehicle is paralleled in the parking area by the user.
The step is finished when the wheel angle is moved to neutral position.
The View mode is changed to Rear View Mode when the Back menu is selected in P3.
x The design of line can be altered by the conference. |
1. |
When the vehicle speed is not satisfied
The logic is performed for 3sec before the step is changed to
View Mode when hold the wheel angle and exceed the limited
speed(10KPH). |
| Menu | REMARK | |||
GARAGE | PARALLEL | TOP VIEW | BACK | ||
Parking Mode Selection | 0 | 0 | 0 | | |
G1 | | | | 0 | |
G2 | | | | 0 | |
P1 | | | | 0 | |
P2 | | | | 0 | |
P3 | | | | 0 | |
Front Impact Sensor (FIS) Repair procedures
Removal
•
Removal of the airbag must be performed according to the precautions/ procedures described previously.
•
Before disconnecting the front impact sensor connec ...
Rear Wheel House Trim Repair procedures
Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protec ...
Canister Close Valve (CCV) Repair procedures
Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the CCV connector.
3.
Measure resistance between the CCV terminal 1 and 2.
4.
Check that the resistance is within the specific ...