>
Specifications |
Items | Specification |
Air spring volume at design position | 1.78x |
Maximum other bellow diameter | 118 mm |
Burst pressure | 31.5 bar |
Minimum operating temperature | -40°C |
Maximum operating temperature | 80°C |
Items | Specification |
Operation voltage | 9 ~ 15 VDC |
Max. perm. Current | 35 A Min |
Lower operation temperature | -40°C |
Upper operation temperature | 70°C |
Storage Temperature | -40°C ~ 90°C |
Items | Specification |
Operation voltage | 9 ~ 15 VDC |
Lower operation temperature | -40°C |
Upper operation temperature | 70°C |
Storage Temperature | -40°C ~ 90°C |
Items | Specification |
Required supply voltage | 5 VDC 5% |
Operation voltage | 5 VDC 10% |
Maximum allowed voltage range | 20 V |
Storage Temperature | -40°C ~ 90°C |
Items | Specification |
Operating pressure | 16.5 bar |
Burst pressure | 40 bar min |
Air tank volume | 5.2 x |
Items | Specification |
Rated Voltage | 12 V DC |
Operating Voltage | 10 ~ 16 V DC |
Operation Temperature | -40°C ~ 75°C |
Storage Temperature | -40°C ~ 90°C |
Item | Tightening torque (kgf.m) | ||
N.m | kgf.m | lb-ft | |
Reservoir tank to crash box | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Reservoir tank to frame housing | 20.0 ~ 30.0 | 2.0 ~ 3.0 | 14.0 ~ 22.0 |
Front height sensor to frame | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Front height sensor to lateral arm | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Solenoid valve to bracket | 8.0 ~ 12.0 | 0.8 ~ 1.2 | 6.0 ~ 9.0 |
Compressor to bracket | 8.0 ~ 12.0 | 0.8 ~ 1.2 | 6.0 ~ 9.0 |
G-sensor to frame | 4.0 ~ 6.0 | 0.4 ~ 0.6 | 3.0 ~ 4.0 |
Compressor & bracket to frame crash box | 35.0 ~ 55.0 | 3.5 ~ 5.5 | 25.0 ~ 40.0 |
Air filter to frame | 4.0 ~ 6.0 | 0.4 ~ 0.6 | 3.0 ~ 4.0 |
Front height sensor to frame | 4.0 ~ 6.0 | 0.4 ~ 0.6 | 3.0 ~ 4.0 |
Feeling valve mounting bracket to frame | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Auto hold
The AUTO HOLD feature keeps the brakes applied after the vehicle comes to a complete
stop when the shift lever is in D, R, or N. The brakes release when throttle is
applied.
Set up
1.Pre ...
Rear Driveshaft (VL-VL TYPE) Repair procedures
Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from rear hub.
Be carefu ...
Front Upper Arm Repair procedures
Removal
1.
Remove the front wheel and tire (A) from front hub .
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
•
Be careful not to damage ...