>
Hyundai Equus Manuals

Hyundai Equus: Air Spring Repair procedures - Air Suspension System - Suspension System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Air Spring Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Suspension System / Air Suspension System / Air Spring Repair procedures

Removal
   
•
Before replacing the relevant parts, use GDS equipment to fully discharge the air from the relevant parts.
(Refer to Air Suspension System - "Repair procedures (Air Injection Procedure)")
•
Be careful when handling the rear air spring, as the lack of structural reinforcement inside the bellows makes it susceptible to bending or stretching if subjected to external forces.
•
When removing an air strut, remove the air connector before proceeding with any other work.
•
Make sure that the orientation of the upper and lower part does not twist during assembly.
•
Check the cleanliness of each part after it is moved. (check for any foreign substances).
•
Ensure that the air injection connector includes a cap that prevents the introduction of foreign substances.
Air Spring
1.
Remove the rear wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Remove the air tube (A).

   
Take car due to the high pressure air in the spring is discharged.
3.
Remove the stabilizer link (A) & height sensor (B).

4.
Loosen the cam bolt (A).

5.
Installation is the reverse of removal.
   
•
Take care not to twist upper and lower.
•
After transportaion, check the cleanliness.
•
Check the cap which prevents entering foreign materials on the connector of air filling portion.
•
Take care due to it is bended or defamed easily by external force.
Coil spring
1.
Remove the rear wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Loosen the nut(A) and then remove the stabilizer link.
Tightening torque :
50.0 ~ 65.0 N.m (5.0 ~ 6.5 kgf.m, 36.0 ~ 47.0 lb-ft)

3.
Loosen the nut and then remove the height sensor(A).
Tightening torque :
4.0 ~ 6.0 N.m (0.4 ~ 0.6 kgf.m, 3.0 ~ 4.0 lb-ft)

4.
Loosen the bolt (A), nuts (B), flange bolt (C), lock nuts (D) and then remove the lower arm.
Tightening torque :
Axle : 140.0 ~ 160.0 N.m (14.0 ~ 16.0 kgf.m, 101.0 ~ 116.0 lb-ft)
Damper : 140.0 ~ 160.0 N.m (14.0 ~ 16.0 kgf.m, 101.0 ~ 116.0 lb-ft)

5.
Installation is the reverse of removal.
6.
Check the alignment.
(Refer to Tires/Wheels - "Alingment")
    Air Spring Description and Operation
    Description Because of the design layout, the air spring and the shock absorber (damper) is separated. The average (target) pressure of rear air spring for normal operation is around 8.5 bar. ...

    Compressor Components and Components Location
    Components 1. Dyer2. Motor3. Connected to tube4. Reverse valve connector5. Connector for motor driveing ...

    See also:

    For best battery service
    The battery is in the trunk. Keep the battery securely mounted. Keep the battery top clean and dry. Keep the terminals and connections clean, tight, and coated with petroleum jelly or t ...

    Description and Operation
    Description Active type ECS is applied and it includes the self leveling function.As shown in the picture, it consists of air spring, damper, reservoir tank, compressor (with dryer), solenoid ...

    Presure Switch Repair procedures
    Inspection 1. Turn ignition switch OFF. 2. Disconnect the E Module connector. 3. Measure resistance between sensor signal terminal and sensor ground terminal. 4. Check that the res ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com