>
Hyundai Equus Manuals

Hyundai Equus: Upper Arm Repair procedures - Air Suspension System - Suspension System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Upper Arm Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Suspension System / Air Suspension System / Upper Arm Repair procedures

Removal
[Front Upper arm]
1.
Removal the front wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Removal the air strut assembly.
(Refer to air strut assembly.)
3.
Disconnect the upper arm (A) with the air strut assembly bracket (B) by loosening the bolt.
Tightening torque :
100.0 ~ 120.0 N.m(10.0 ~ 12.0 kgf.m, 72.0 ~ 87.0 lb-ft)

4.
Installation is the reverse of removal.
[Rear Upper arm]
Replacement the front upper arm
1.
Remove the rear wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Disconnect the rear front upper arm (A) from the rear axle by loosening the bolt & nut.
Tightening torque :
120.0 ~ 140.0 N.m(12.0 ~ 14.0 kgf.m, 87.0 ~ 101.0 lb-ft)

3.
Disconnect the rear front upper arm (A) from the rear sub frame by loosening the bolt & nut.
Tightening torque :
120.0 ~ 140.0 N.m(12.0 ~ 14.0 kgf.m, 87.0 ~ 101.0 lb-ft)

4.
Installation is the reverse of removal.
Replacement the rear upper arm
1.
Remove the rear wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Disconnect the rear upper arm (B) from the rear axle by loosening the split pin & nut (A).
Tightening torque :
80.0 ~ 90.0 N.m(8.0 ~ 9.0 kgf.m, 58.0 ~ 65.0 lb-ft)

3.
Disconnect the rear upper arm from the rear carrier using a SST (09568-2J100).

4.
Disconnect the rear front upper arm (A) from the rear sub frame by loosening the flange bolt & lock nut.
Tightening torque :
120.0 ~ 140.0 N.m(12.0 ~ 14.0 kgf.m, 87.0 ~ 101.0 lb-ft)

5.
Installation is the reverse of removal.
   
Do not use the lock nuts again.
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the ball joint for rotating torque.
    Stabilizer Bar Repair procedures
    Removal [Front Stabilizer Bar] 1. Removal the front wheel & tire. Tightening torque : 90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft) 2. Disconnect the stabilizer link (A) ...

    Trailing Arm Repair procedures
    Removal 1. Remove the rear wheel & tire. Tightening torque : 90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft) 2. Disconnect the trailing arm (A) from the rear axle by loosening ...

    See also:

    Start-Up
    You can start the engine without inserting the key. For detailed information refer to the Engine Start/Stop Button in section 5. CAUTION To prevent damaging the Smart Key : Keep the Smart Key ...

    Repair procedures
    Inspection Front Door Lock Module Inspection 1. Remove the front door trim. (Refer to Body - "Front Door Trim") 2. Remove the front door module. (Refer to Body - "Front Door Module") 3. ...

    Output Speed Sensor Specifications
    Specifications x Type: Hall effect sensor x Specifications Operation condition (°C)°F((-)40~150)) -40~302Air gap(mm)in.1.3(0.0512)Output voltageHigh1.4Low0.7 ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com