>
Hyundai Equus Manuals

Hyundai Equus: Front Washer Motor Repair procedures - Windshield Wiper/Washer - Body Electrical System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Front Washer Motor Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Washer Motor Repair procedures

Removal
   
1)
When servicing the washer pump, be careful not to damage the washer pump seal.
2)
Do not operate the washer pump before filling the washer reservoir.
Failure to do so could result in premature pump failure.
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front bumper cover.
(Refer to Body - "Front Bumper")
3.
Remove the front head lamp assembly.
(Refer to Lighting System / Head Lamp)
4.
Remove the washer hose and the washer motor connector (A) and the washer fluid level sensor connector (B).

5.
Remove the washer reservoir 2 bolts.

6.
Remove the mounting bolts of air suspension reserive tank under the washer reserive in order to make easier to remove washer tank. But, do not disconnect air hose.
(Refer to Suspension - "Front Suspension System")
7.
Remove the washer reserior after loosening the mounting bolt from the lower and of washer reserivor
Inspection
Front Washer Motor
1.
With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
   
Before filling the reservoir tank with water, check the filter for foreign material or contamination. if necessary, clean the filter.
2.
Connect positive (+) battery cables to terminal 2 and negative (-) battery cables to terminal 1 respectively.
3.
Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles.
4.
If they are abnormal, replace the washer motor.
(Connector NO.1 : Windshield washer (+), 2: Ground)

Washer Fluid Level Sensor Switch
1.
Disconnect the negative(-) battery terminal.
2.
Drain the washer fluid less than 650 cc.
3.
Check for continuity between the No. 1 and No.2 terminal in each float position.
There should be continuity when the float is down.
There should be no continuity when the folat is up.
4.
If the continuity is not as specified, replace the washer fluid level switch

Head Lamp Washer Motor
1.
With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
   
Before filling the reservoir tank with water, check the filter for foreign material or contamination. if necessary, clean the filter.
2.
Connect positive (+) battery cables to terminal 2 and negative (-) battery cables to terminal 1 respectively.
3.
Check that the motor operates normally and the washer motor runs and water sprays from the head lamp nozzles.
4.
If they are abnormal, replace the washer motor.
Installation
1.
Install the washer reservoir.
   
Before installing the pump motor, check the filter for foreign material or conamination. If necessary clean the filter in to the pump motor.
2.
Install the washer motor hose and connectors.
3.
Install the air suspension reserve tank bolts.
4.
Install the head lamp assembly.
5.
Install the front bumper cover.
    Front Wiper Motor Repair procedures
    Removal 1. Remove the windshield wiper arm (A) and blade after removing a nut. Tightening torque : 27 ~ 31 N.m (2.8 ~ 3.2 kgf.m, 20 ~ 23 lb-ft) 2. If necessary of removing the wiper blad ...

    Rain Sensor Components and Components Location
    Components and Components Location 1. Horizontal light sensor2. Vertical light sensor3. Solar load sensor4. Rain sensor - left5. Rain sensor - right ...

    See also:

    Driving your vehicle
    WARNING - ENGINE EXHAUST CAN BE DANGEROUS! Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the windows immediately. Do not inh ...

    Intake Actuator Description and Operation
    Description The intake actuator is located at the blower unit. It regulates the intake door by a signal from the control unit. Pressing the intake selection switch will shift between recirculat ...

    Repair procedures
    Removal Parking Brake Shoe 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the brake caliper and Rear disc brake. (Refer to Bra ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com