>
Hyundai Equus Manuals

Hyundai Equus: Electric Parking Brake (EPB) Repair procedures - Parking Brake System - Brake System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Electric Parking Brake (EPB) Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Brake System / Parking Brake System / Electric Parking Brake (EPB) Repair procedures

Removal
1.
Release the parking brake by pushing the EPB switch.
2.
Turn ignition switch off and disconnect the battery (-) cable from the battery.
3.
Remove the canister service cover in the trunk.

4.
Remove the canister and the bracket.
(Refer to Emission Control System - “Canister”)
5.
Remove the canister bracket (A).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

6.
Disconnect the EPB connector (A).

7.
Remove the EPB bracket No. 2 after removing the bolt.
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

8.
Remove the rear brake disc.
( Refer to Brake System - "Rear Disc Brake”)
9.
Remove the parking brake cable after removing the bolt (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 Ib-ft)

10.
Remove the parking brake cable (A) from the DIH operating lever assembly. (Both left and right side)

11.
Remove the mounting bolt for parking brake cable.
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

12.
Remove the EPB bracket No. 1 mounting bolt.
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)
13.
Remove the EPB and the bracket No. 2 from the sub flame.
14.
Remove the EPB from the bracket No. 2 after mounting nut (A).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

   
1.
Do not impact on the EPB.
2.
Do not disassemble the EPB.
3.
Operate the EPB switch after precise installation of the cable and all parts.
4.
Do not pull the brake inner cable after assembly.
Installation
1.
Installation is reverse of removal.
2.
Adjust the rear brake shoe clearance.
(1)
Remove the plug from the disc.

(2)
Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 6 notches in the opposite direction.
3.
Check that the brake operates normally by pushing the EPB switch more than 3 times after installing the EPB module.
A.
The parking brake indicator lamp must be on when the parking brake pedal is depressed and must be off when the pedal is released.
B.
Must be held on 30% uphill
C.
No brake drag after the parking brake is released.
    Electric Parking Brake (EPB) Components and Components Location
    Components 1. EPB2. Bracket No.13. Bracket No.24. EPB Extension wiring harness5. Parking brake cable ...

    Electric Parking Brake (EPB) Schematic Diagrams
    Circuit Dragram ...

    See also:

    Fuel Pressure Sensor (FPS) Repair procedures
    Inspection 1. Connect the GDS on the Data Link Connector (DLC). 2. Check the output voltage of fuel pressure sensor (FPS). Specification: Refer to “Specification” Removal 1. Tu ...

    Engine Coolant Temperature Sensor (ECTS) Specifications
    Specification TemperatureResistance (kx)°C°F-40-4048.14-20-414.13 ~ 16.830325.7920682.31 ~ 2.59401041.15601400.59801760.32 ...

    Unlocking
    To unlock: 1. Carry the Smart Key. 2. Either put your hand in the driver’s outside door handle or press the Door Unlock button on the Smart Key. 3. The driver’s door will unlock. The haza ...

    Categories

    Hyundai Equus Manuals

    2011-2026 Copyright www.heqmanual.com