>
Hyundai Equus Manuals

Hyundai Equus: Power Steering Gear Box Repair procedures - Electro Hydraulic Power Steering - Steering System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Power Steering Gear Box Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Steering System / Electro Hydraulic Power Steering / Power Steering Gear Box Repair procedures

Replacement
1.
Drain the power steering fluid.
2.
Remove the front wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
3.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
Tightening Torques :
32.0 ~ 37.0 N.m(3.3 ~ 3.8 kgf.m, 24.0 ~ 27.4 lb-ft)

   
Keep the neutral-range to prevent the damage of the clock spring inner cable when you handlethe steering wheel.
4.
Loosen the castle nut.
Tightening torque :
85.0 ~ 110.0 N.m (8.5 ~ 11.0 kgf.m, 62.0 ~ 80.0 lb-ft)

5.
Disconnect the tie-rod end (A) from the knuckle using a SST (09568-2J100).
Tightening torque :
88.0 ~ 108.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.4 lb-ft)

6.
Loosen the tube bolts and then disconnect the pressure and return tube.

7.
Remove the steering gear box bracket (A) by loosening the bolts.
Tightening torque :
20.0 ~ 30.0 N.m (2.0 ~ 3.0 kgf.m, 15.0 ~ 22.0 lb-ft)

8.
Remove the steering gear box (A) by loosening the bolts.
Tightening torque :
85.0 ~ 110.0 N.m (8.5 ~ 11.0 kgf.m, 62.0 ~ 80.0 lb-ft)

9.
Installation is the reverse of the removal.
Inspection
1.
Rack
A.
Check for rack tooth face damage or wear.
B.
Check for oil seal contact surface damage or wear.
C.
Check for bending or twisting of rack.
D.
Check for oil seal ring damage or wear.
E.
Check for oil seal damage or wear.

    Power Steering Gear Box Components and Components Location
    Components 1. Tie rod end2. Lock nut3. Bellows Clip4. Bellows5. Bellows band6. Steering gear box ...

    Power Steering Hose Repair procedures
    Replacement - Refer to the components illustration during removal or installation. - When installing, be sure to connect between hose to tube using a clamp as shown in the illustration. - ...

    See also:

    If engine turns over normally but does not start
    1. Check fuel level. 2. With the Engine Start/Stop Button in the OFF position, check all connectors at ignition coils and spark plugs. Reconnect any that may be disconnected or loose. 3. If the en ...

    Fuel Pressure Control Valve Description and Operation
    Description Fuel Pressure Control Valve is installed on the high pressure fuel pump and controls fuel flow flowing into the injectors in accordance with the ECM signal calculated based on vario ...

    Main Crash Pad Assembly Repair procedures
    Replacement     • Put on gloves to protect your hands.     • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply p ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com