>
Hyundai Equus Manuals

Hyundai Equus: Reservoir Tank Repair procedures - Air Suspension System - Suspension System - Hyundai Equus VI 2009-2025 Service ManualHyundai Equus: Reservoir Tank Repair procedures

Second generation VI (2009–2025) / Hyundai Equus VI 2009-2025 Service Manual / Suspension System / Air Suspension System / Reservoir Tank Repair procedures

Removal
   
•
Before replacing the relevant parts, use GDS equipment to fully discharge the air from the relevant parts.
(Refer to Air Suspension System - "Repair procedures (Air Injection Procedure)")
•
This system combines a sensor and electronic parts with mechanical components, so be careful not to subject the system to strong impacts.
•
If any pins are visible inside the electric signaling connector, do not expose it to water.
•
A plug protects the air inlet of the reservoir tank from dust or other particles. Do not remove the plug except when assembling or disassembling the reservoir tank.
•
DO NOT hold any parts by their electric wires while moving them, as the weight of the part may damage the wire or connection during transport.
•
Do not pile components on top of each other.
•
Do not apply power to operate the compressor directly (may cause malfunctions/overheating).
•
Be careful not to break any circuits by twisting or bending the cables.
•
DO NOT drop any parts.
•
Check the color of each air hose before connecting it. After connecting a hose, pull it to ensure that the connection holds firm.
•
The air connection section of the air hose includes a dust cover to prevent the introduction of foreign substances. DO NOT remove this cap for any process besides connecting the hose.
•
When installing an air hose, be careful not to kink the hose.
•
DO NOT reuse the air hose connector connected to an air hose assembly after it has been disassembled.
•
The markings on both ends of the air hose distinguishes the assembly, so be careful not to peel it off.
1.
Removal the front bumper.
(Refer to Body - "Front bumper")
2.
Removal the left head amp.
(Refer to Body Electrical System - "Head lamp leveling device")
3.
Removal the nut & clip & air hose.

4.
Disconnect the reservoir tank (A) by remove the bolt & air tube.

   
•
Separate completely after bleeding air slowly.

Installation
1.
Install the reservoir tank (A).

2.
Install the nut & clip & air hose.

   
•
With vehicles sit down in the floor, do not inflate air.
•
When air filling, always do it after lifting up the vehicle.
•
Take care not to drop.
•
Confirm the tube color in installation process.
•
Confirm that whether the tube is escaped a not by puling it.
•
Assemble with specific torque.
•
Assemble with out dust cap removal.
•
Remove cap and check escape by inserting hose.
Air filling
System air filling machine

System air filling is done at the factory before delivering the vehicle. In case of workshop, it should be done after replacing the related parts or the system air was drained because of other repairing works. Follow the recommended procedure for system air filling.
1.
Prepare the compressed air (12bar) using the air filling machine.
2.
Connect the air outlet nozzle in the machine to the air filling valve (RH side of engine room) in the vehicle.
3.
Ignition ON (engine off) and connect the scanner.
4.
Lift up the vehicle. (all wheels must be rebounded)
5.
Opening the lever in the machine, starts to fill the air from filling machine to the reservoir tank in the vehicle until the whistle sound stops.
6.
Enter the menu of system air filling in the scanner and follow the instruction in the scanner.
The compressed air will be transferred to the front air spring and rear air spring accordingly by operating the compressor and solenoid valves.
7.
Take down the vehicle after completing the air filling.
   
•
Do not face the person because the used air is high pressure.
•
Be sure to check the installing states of each connecting portion before working.
•
Replace filter of air filler and moisture remove 1 time every 2 years.
Air Filling/Venting Setup
1.
Connect to the GDS diagnostic.

    Reservoir Tank Description and Operation
    Description The volume is 5.2 liter and the maximum operation pressure is 16bar. (Bursting pressure: 40bar) The pressure of reservoir tank is monitored every 30 min while driving. ...

    ECU Components and Components Location
    Components Location 1. ECU2. ECU bracket3. ECU support ...

    See also:

    Compass Mirror Repair procedures
    Adjustment Calibration procedure If the display read "C", calibrate the compass. 1. Driving the vehicle in a circle at less than 8km/h 3 times or until the compass heading appears. 2. Drivin ...

    Battery recharging by vehicle
    After a jump start from a good battery, run the engine for 20-30 minutes at idle or driving the vehicle before it is shutoff. Vehicle may not restart if you shut it off before the battery had chan ...

    Changing the coolant
    Have coolant changed by an authorized EQUUS dealer according to the Maintenance Schedule at the beginning of this section. CAUTION Put a thick cloth around the radiator cap before refilling the co ...

    Categories

    Hyundai Equus Manuals

    © 2011-2025 Copyright www.heqmanual.com