>
Hyundai Equus Manuals

Hyundai Equus: General Safety Information and Caution - Air Conditioning System - Heating, Ventilation and Air Conditioning - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: General Safety Information and Caution

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Heating, Ventilation and Air Conditioning / Air Conditioning System / General Safety Information and Caution

Instructions
When Handling Refrigerant
1.
R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be sure to wear gloves.
2.
It is standard practice to wear goggles or glasses to protect your eyes, and gloves to protect your hands. If refrigerant splashes into your eyes, wash them with clean water immediately.
3.
The R-134a container is highly pressurized. Never leave it in a hot place, and check if storage temperature is below 52°C (126°F)
4.
An electronic leak detector should be used to check the system for refrigerant leakage. Bear in mind that the R-134a, upon coming into contact with flame, produces phosgene, a highly toxic gas.
5.
Use only recommended lubricant for R-134a systems. If lubricants other than the recommended one used, system failure may occur.
6.
PAG lubricant absorbs moisture from the atmosphere at a rapid rate, therefore the following precautions must be observed:
A.
When removing refrigerant components from a vehicle, cap the components immediately to prevent entry of moisture.
B.
When installing refrigerant components to a vehicle, do not remove the cap until just before connecting the components.
C.
Complete the connection of all refrigerant tubes and hoses without delay to prevent the A/C system from taking on moisture.
D.
Use the recommended lubricant from a sealed container only.
7.
If an accidental discharge in the system occurs, ventilate the work area before resume of service.

When Replacing Parts on A/C System
1.
Never open or loosen a connection before discharging the system.
2.
Seal the open fittings of components with a cap or plug immediately to prevent intrusion of moisture or dust.
3.
Do not remove the sealing caps from a replacement component until it is ready to be installed.
4.
Before connecting an open fitting, always install a new sealing ring. Coat the fitting and seal with refrigerant oil before making the connection.

When Installing Connecting Parts
Flange With Guide Pin
Check the new O-ring for damage (use only the specified) and lubricate by using compressor oil. Tighten the nut to the specified torque.

Handling Tubing and Fittings
The internal parts of the refrigeration system will remain in a state of chemical stability as long as pure moisture-free refrigerant and refrigerant oil are used. Abnormal amounts of dirt, moisture or air can upset the chemical stability and cause problems or serious damage.
The Following Precautions Must Be Observed
1.
When it is necessary to open the refrigeration system, have everything you will need to service the system ready so the system will not be left open any longer than necessary.
2.
Cap or plug all lines and fittings as soon as they are opened to prevent entrance of dirt and moisture.
3.
All lines and components in parts stock should be capped or sealed until they are ready to be used.
4.
Never attempt to rebind formed lines to fit. Use the correct line for the installation you are servicing.
5.
All tools, including refrigerant dispensing manifold, gauge set manifold and test hoses, should be kept clean and dry.
    Air Conditioning System
    ...

    Description and Operation
    Refrigeration Cycle ...

    See also:

    Troubleshooting
    Troubleshooting SymptomProbable causeRemedyExcessive play in steeringLoose yoke plugRetightenLoose steering gear mounting boltsRetightenLoose or worn tie rod endRetighten or replace as necessaryS ...

    Operating Door Locks From Inside the Vehicle
    With the Door Lock Button : To unlock a door, push the door lock button (1) to the “Unlock” position. The red mark (2) on the door lock button will be visible. To lock a door, push the ...

    Rear Seat Belt Buckle Repair procedures
    Replacement [Sedan 6:4] 1. Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly") 2. Loosen the mounting bolt, and then remove the rear seat belt buckle (A). [L ...

    Categories

    Hyundai Equus Manuals

    2011-2026 Copyright www.heqmanual.com