>
Hyundai Equus Manuals

Hyundai Equus: Description and Operation - Tire Pressure Monitoring System - Suspension System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Description and Operation

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Suspension System / Tire Pressure Monitoring System / Description and Operation

Description
Tread Lamp
-
Tire Under Inflation / Leak Warning.

1.
Turn on condition
A.
When tire pressure is below allowed threshold
B.
When rapid leak is detected by the sensor.
2.
Turn off condition
A.
Under-inflation ; When tire pressure is above (warning threshold + hysteresis).
B.
Rapid Leak ; When tire pressure is above (leak warning threshold).
Wheel Location
1.
Turn on condition
A.
At the same time as TREAD Lamp.
B.
Indicates wheel location where under inflation / leak has occurred.
2.
Turn off condition
A.
At the same time as TREAD Lamp.
   
If wheel locations change in between Ignition cycles, then the system assumes the previous Auto-Located position. Once Auto-Location completes on the current Ignition cycle, the correct lamp will be lit.
DTC Warning

1.
Turn on condition
A.
When the system detects a fault that is external to the receiver / initator / sensor.
B.
When the system detects a receiver fault.
C.
When the system detects an initiator fault.
D.
When the system detects a sensor fault.
2.
Turn off condition
A.
If the fault is considered as 'critical', then the lamp is held on throughout the current Ignition cycle (even if the DTC has been demoted). This is because it is important to bring the problem to the drivers attention. On the following Ignition cycle, the demotion conditions will be re-checked. If the demotion conditions occur, the lamp will be turned off. It will be held on until DTC demotion checking is completed.
B.
'Non critical' faults are those that can occur temporarily e.g. vehicle battery under voltage. The lamp is therefore turned off when the DTC demotion condition occurs.
System Fault
1.
General Function
A.
The system monitors a number of inputs across time in order to determine that a fault exists.
B.
Faults are prioritized according to which has the most likely cause.
C.
Maximum fault store is equal to 15.
D.
Certain faults are not covered through DTC. The main ones are:
1)
Sensor thermal shutdown (239°F/115°C)
2)
Ignition Line stuck ; requires observation of lamps at Ignition ON to diagnose.
    Schematic Diagrams
    Circuit Diagram NO.Function1BAT.2IGN3CAN_High4CAN_Low5GND6- ...

    TPMS Sensor Description and Operation
    Description 1. General description (1) WU is a sensor placed in the tire that reports pressure and temperature. (2) The WU is mounted inside the wheels, fixed to the valve. The angle between ...

    See also:

    Oil Pump Components and Components Location
    Components Location 1. Oil seal2. Reaction shaft3. Housing4. Cover5. O-Ring6. Reaction shaft7. Snap ring8. Needle bearing9. 8LR/B return spring10. 8LR/B piston ...

    27 Brake Control Solenoid Valve Repair procedures
    Inspection 1. Turn ignition switch OFF. 2. Disconnect the E Module connector. 3. Measure resistance between sensor signal terminal and sensor ground terminal. 4. Check that the res ...

    Special Service Tools
    Special Service Tools Tool(Number and Name)IllustrationUse09581-11000Piston expanderSpreading the front disc brake piston.09568-2J100Ball joint removerRemoval of the rear assist arm and tie rod e ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com