>
Hyundai Equus Manuals

Hyundai Equus: Rear Disc Brake Repair procedures - Brake System - Brake System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Rear Disc Brake Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Brake System / Brake System / Rear Disc Brake Repair procedures

Removal
1.
Remove the rear wheel & tire.
Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
2.
Loosen the hose eye-bolt (B) and caliper mounting bolts (C), then remove the rear caliper assembly (A).
Tightening torque
Brake hose to caliper:
24.5 ~ 29.4 N.m (2.5 ~ 3.0 kgf.m, 18.1 ~ 21.7 lb-ft)
Caliper assembly to carrier:
63.7 ~ 73.5 N.m (6.5 ~ 7.5 kgf.m, 47.0 ~ 54.2 lb-ft)

3.
Remove the rear brake disc by loosening the screws (A).

Replacement
Rear Brake Pads
1.
Loosen the guide rod bolt (B) and pivot the caliper up out of the way.
Tightening torque :
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

2.
Replace pad shim, pad retainers (C) and brake pads (B) in the caliper bracket (A).

Inspection
Rear Brake Disc Thickness Check
1.
Check the brake pads for wear and fade.
2.
Check the brake disc for damage and cracks.
3.
Remove all rust and contamination from the surface, and measure the disc thickness at 8 points, at least, of same distance (5mm) from the brake disc outer circle.
Brake disc thickness
Standard: 20mm (0.79in)
Service limit: 18.4mm (0.72in)
Deviation: less than 0.005mm (0.0002in)

4.
If wear exceeds the limit, replace the discs and pad assembly left and right of the vehicle.
Rear Brake Pad Check
1.
Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.
Pad thickness
Standard value: 9mm (0.35in)
Service limit: 2.0 mm (0.0787 in)
2.
Check that grease is applied, to sliding contact points and the pad and backing metal for damage.
Rear Brake Disc Runout Check
1.
Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc.
Brake disc runout
Limit: 0.05mm (0.002in.) or less (new one)

2.
If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.
3.
If the runout exceeds the limit specification, install the brake disc after turning it 180° and then check the runout of the brake disc again.
4.
If the runout cannot be corrected by changing the position of the brake disc, replace the brake disc.
Installation
1.
Installation is the reverse of removal.
2.
Use a SST (09581-11000) when installing the brake caliper assembly.
3.
After installation, bleed the brake system.
(Refer to Brake System - "Brake System Bleeding")
    Rear Disc Brake Components and Components Location
    Components 1. Guide rod bolt2. Bleed screw3. Caliper body4. Caliper bracket5. Inner pad shim6. Brake pad7. Pad retainer ...

    Brake Switch Repair procedures
    Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the lower crash pad. (Refer to the Body - "Crash Pad") 3. Disconnect the stop lamp switch con ...

    See also:

    Head Lamps Repair procedures
    Inspection Head Lamp Relay Inspection 1. Pull out the head lamp relay (Low) (A) from the engine compartment relay box. A : Head lamp(Low) relay 2. Check for continuity between terminals. The ...

    Sunroof Glass Repair procedures
    Replacement     • Put on glove to protect your hands. 1. Remove both sides of the decoration cover (A). 2. Loosen the mounting screws, then remove the glass (A) by ...

    Repair procedures
    Replacement     • Be careful not to damage the fender and body.     • When removing the clips, use a clip remover. 1. Loosen the front wheel ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com