>

Hyundai Equus: Repair procedures - Parking Brake System - Brake System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Repair procedures

Removal
Parking Brake Shoe
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear tire and wheel.
3.
Remove the brake caliper and Rear disc brake. (Refer to Brake System - "Rear Disc Brake")
4.
Remove the parking brake cable (B), after removing the bolt (A).

Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

5.
Remove the shoe hold down pin (A) and the spring (B) by pushing the retainer spring and turning the pin.

6.
Remove the adjuster assembly (B) and the lower return spring (A).

7.
Remove the upper return spring (C) and the brake shoes (D).

8.
Remove the operating lever assembly (E).
Installation
Parking Brake Shoe
1.
Install the operating lever assembly (E).

2.
Install the upper return spring (C) and the brake shoes (D).
3.
Install the adjuster assembly (B) and the lower return spring (A).

4.
While pressing the spring, install the brake shoe hold down pin (A) and spring (B).

5.
Install the parking brake cable (B), then install the bolt (A).

   
How to install the DIH cable (Quick Fit type)
1.
Put the inner cable into the knuckle hole in DIH lever operating direction when installing the cable (B).
2.
Confirm by pulling the cable that cable is fixed certainly before installing the bolt (A).
6.
Install the rear brake disc, then adjust the rear brake shoe clearance.
(1)
Remove the plug from the disc.

(2)
Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 5 notches in the opposite direction.
7.
Install the brake caliper assembly.
(Refer to Brake System - "Rear Disc Brake")
8.
Install the tire and wheel.
9.
If the parking brake shoe or the brake disc are replaced a newly one, perform the brake shoe bed-in procedure.
(1)
While operating the parking brake pedal for 147N (15kgf, 33lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 60kph (37.3 mph).
(2)
Repeat the above procedure more than two times.
(3)
Must be held on at 30% uphill.
   
After adjusting parking brake, notice following matter;
1.
Must be free from troubles when the parking pedal is operated at 981 N (100 kgf, 220 lb).
2.
Check that all parts move smoothly.
3.
The parking brake indicator lamp must be on after the parking pedal is worked and must be off after the pedal is released.
Adjustment
Parking Brake Shoe Clearance Adjustment
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear tire and wheel.
3.
Remove the plug from the disc.

4.
Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 5 notches in the opposite direction.
5.
Install the plug on disc and then rear wheel & tire.
    Components and Components Location
    Components 1. Backing plate2. Operating lever3. Upper spring4. Lower spring5. Adjuster6. Shoe hold down spring7. Shoe hold down pin8. Parking brake shoe9. Cup washer ...

    Electric Parking Brake (EPB) Description and Operation
    Description The EPB is an electronic parking brake. The EPB is different from existing parking systems which operated with the brake pedal or the lever type. The EPB system sends the signal t ...

    See also:

    Fuel Tank Repair procedures
    Removal 1. Release the residual pressure in fuel line. (Refer to Fuel Delivery System - "Release Residual Pressure in Fuel Line") 2. Turn the ignition switch OFF and disconnect the negative ...

    Sunroof Motor Repair procedures
    Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the overhead console then remove the sun roof motor mounting screws (3EA). And then remove the sunroof motor (A) after ...

    Oil Filter Repair procedures
    Replacement 1. Draining ATF totally. 2. Remove the oil pan (A). 3. Must be replaced by new oil pan.     Integrated filter in the oil pan is not replaceable. 4. Add ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com