>
Hyundai Equus Manuals

Hyundai Equus: Pre-active Seat Belt (PSB) Repair procedures - Seat Belt Pretensioner - Restraint - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Pre-active Seat Belt (PSB) Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Restraint / Seat Belt Pretensioner / Pre-active Seat Belt (PSB) Repair procedures

Removal
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the safety belt (A) by turning it in the direction of arrow using a flat-head screwdriver.

3.
Remove the center pillar lower trim.
(Refer to Body - "Center Pillar Trim")
4.
Remove the center pillar upper trim.
(Refer to Body - "Center Pillar Trim")
5.
After loosening the mounting bolt, then remove the front seat belt lower anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

6.
Loosen the front seat belt webbing guide (A) mounting bolts.

7.
After disconnecting the pretensioner connector lock pin, remove the front seat belt pretensioner connectors (A), loosen the mounting bolts, then remove the front seat belt pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

Installation
1.
Turn the ignition switch OFF.
2.
Disconnect the battery negative cable and wait for at least three minutes.
3.
Install in the reverse order of removal.
4.
Reconnect the battery negative cable.
5.
After installing the seat belt pretensioner, confirm proper system operation:
Turn the ignition switch ON; the SRS indicator light should turn on for about six seconds and then go off.
PSB Variant Coding
When replacing a PSB of the driver’s or passenger’s seat with a new one, be sure to carry out the Variant Coding procedure using GDS. (Only for vehicles without SCC)
   
PSB variants are coded for vehicles equipped with SCC. Therefore, Variant Coding should be performed only for vehicles without SCC.
PSB Variant Coding
1.
Turn the ignition switch OFF.
2.
Connect the GDS.
3.
Turn the ignition switch ON without the engine running.
4.
Select "PSB-LH" or "PSB-RH", and then select "PSB Variant Coding".

5.
Follow the instructions on the screen, and then press the "OK" button.

6.
Click "C1" if the vehicle is sedan type.
Click "C2" if the vehicle is limousine type.

7.
Click "C1" for vehicles with LDWS.
Click "C2" for vehicles without LDWS.

8.
Select the "OK" button after the "Complete" message has appeared.

    Pre-active Seat Belt (PSB) Schematic Diagrams
    Circuit Diagram ...

    Brake System
    ...

    See also:

    Rear Door Outside Handle Repair procedures
    Replacement 1. Remove the hole plug (B). 2. After loosening the mounting bolt, then remove the rear door outside handle cover (A). Tightening torque : 6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ...

    Description and Operation
    Description Control Function This system supports 3 kinds of main function.(Front/Rear video display function, Expected trace of wheels display function, Parking guide function) The Front/Rea ...

    Base curb weight
    This is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment. ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com