>
Hyundai Equus Manuals

Hyundai Equus: Front Hub / Knuckle / Tone Wheel Repair procedures - Front Axle Assembly - Driveshaft and axle - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Front Hub / Knuckle / Tone Wheel Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub / Knuckle / Tone Wheel Repair procedures

Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub .

   
Be careful not to damage to the hub bolts when removing the front wheel and tire .
3.
Remove the brake caliper mounting bolts, and then hold the brake caliper assembly (A) with wire.
Tightening torque :
80.0 ~ 100.0 Nm (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

[Air Suspension Type]

4.
Loosen the brake disc mount screw then remove the brake disc (A).
Tightening torque :
4.9 ~ 5.8 Nm(0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

5.
Disconnect the wheel speed sensor (A) from knuckle.

6.
Remove the tie rod end ball joint from the knuckle.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Disconnect the ball joint (D) from knuckle (C) using the special tool (09568-4A000).
Tightening torque :
88.3 ~ 107.9 Nm (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.5 lb-ft)

   
Apply a few drops of oil to the special tool. (Boot contact part)
7.
Loosen the tension arm mount nut (A), and then remove the tension arm (B).
(1)
Remove the split pin (C).
(2)
Remove the castle nut (D).
(3)
Disconnect the ball joint (B) from knuckle (A) using the special tool. (09568-4A000)
Tightening torque :
137.3 ~ 156.9 Nm (14.0 ~ 16.0 kgf.m, 101.2~115.7 lb-ft)

   
Be careful not to damage the boot and rotor teeth.
8.
Loosen the lateral mount nut.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Disconnect the ball joint (C) from knuckle (D) using the special tool.(09568-4A000)
Tightening torque :
90.0 ~ 110.0 Nm (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

9.
Remove the hub and knucke assembly (C).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Disconnect the ball joint from knuckle using the special tool (09568-4A000).
Tightening torque :
35.0 ~ 45.0 Nm (3.5 ~ 4.5 kgf.m, 25.3 ~ 32.5 lb-ft)

10.
Remove the hub assembly (B) from knuckle assembly.
Tightening torque :
80.0 ~ 100.0 Nm (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

11.
Loosen the dust cover mount bolts and then remove the dust cover (B) from knuckle (A).
Tightening torque :
7.0 ~ 11.0 Nm (0.7 ~ 1.1 kgf.m, 5.0 ~ 7.9 lb-ft)

12.
Installation is the reverse order of removal.
Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the knuckle for cracks.
4.
Check the bearing for cracks or damage.
    Front Hub / Knuckle / Tone Wheel Components and Components Location
    Component location 1. Front knuckle assembly2. Hub assembly3. Dust cover4. Brake disc ...

    Rear Axle Assembly
    ...

    See also:

    Power Steering Hose Repair procedures
    Replacement - Refer to the components illustration during removal or installation. - When installing, be sure to connect between hose to tube using a clamp as shown in the illustration. - ...

    Airbag Module Disposal Description and Operation
    Airbag Disposal Special tool required Deployment tool 0957A-34100A Before scrapping any airbags or side airbags (including those in a whole vehicle to be scrapped), the airbags or side airba ...

    Passenger Airbag (PAB) Module Description and Operation
    Description The passenger airbag (PAB) is installed inside the crash pad and protects the front passenger in the event of a frontal crash. The SRSCM determines if and when to deploy the PAB. ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com