>
Hyundai Equus Manuals

Hyundai Equus: Lower Arm Repair procedures - Air Suspension System - Suspension System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Lower Arm Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Suspension System / Air Suspension System / Lower Arm Repair procedures

Removal
[Front Lower Arm]
Replacement the lateral arm
1.
Removal the front wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Disconnect the lateral arm (A) from the air strut assembly bracket by loosening the bolt & nut.
Tightening torque :
140.0 ~ 160.0 N.m(9.0 ~ 11.0 kgf.m, 101.0 ~ 116.0 lb-ft)

3.
Removal the split pin and castle nut.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)

4.
Disconnect the lateral arm (A) from the front knuckle using a SST (09568-2J100).

5.
Disconnect the lateral arm (A) from the frame by loosening the bolt & nut.
Tightening torque :
140.0 ~ 160.0N.m(14.0 ~ 16.0kgf.m, 101.0 ~ 116.0 lb-ft)

6.
Installation is the reverse of removal.
   
Do not use the lock nuts again.
Replacement the tension arm
1.
Remove the front wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Disconnect the brake hose (A) from the tension arm by loosening the bolt.

3.
Removal the split pin and castle nut.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 6.5 ~ 8.0 lb-ft)

4.
Disconnect the tension arm (A) from the front knuckle using a SST (09568-2J100).

5.
Disconnect the tension arm (A) from the sub frame by loosening the bolt.
Tightening torque :
140.0 ~ 160.0N.m(14.0 ~ 16.0kgf.m, 101.0 ~ 116.0 lb-ft)

6.
Installation is the reverse of removal.
[Rear Lower Arm]
1.
Remove the rear wheel & tire.
Tightening torque :
90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft)
2.
Remove the air tube (A).

3.
Disconnect the rear stabilizer link (A) & height sensor (B) from the rear lower arm by loosening the nut.

4.
Loosen the cam bolt & lock nut and then remove the lower arm (A).

5.
Disconnect the air spring from the rear lower arm by loosening the bolt (A).

6.
Installation is the reverse of removal.
   
•
Take care not to twist upper and lower.
•
After transportaion, check the cleanliness.
•
Check the cap which prevents entering foreign materials on the connector of air filling portion.
•
Take care due to it is bended or defamed easily by external force.
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the ball joint for rotating torque.
    G Sensor Repair procedures
    Removal     • be careful to avoid excessive external shock. • connectors to avoid damage to the connector pins. G-sensor FL 1. Remove the front bumper. (Refer to ...

    Stabilizer Bar Repair procedures
    Removal [Front Stabilizer Bar] 1. Removal the front wheel & tire. Tightening torque : 90.0 ~ 110.0 N.m(9.0 ~ 11.0 kgf.m, 65.0 ~ 80.0 lb-ft) 2. Disconnect the stabilizer link (A) ...

    See also:

    Fluid Repair procedures
    Service Adjustment Procedure Oil level Check     A check of ATF level is not normally required during scheduled services. If an oil leak is found, perform the oil level chec ...

    Schematic Diagrams
    Circuit Diagram ...

    Yaw-rate and Lateral G Sensor Description and Operation
    Description The ESP system is the shorten word of Electronic Stability Control system. This system recognizes a critical driving condition by Yaw-rate sensor, Lateral acceleration sensor and St ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com