>
Hyundai Equus Manuals

Hyundai Equus: Intake Manifold Repair procedures - Intake And Exhaust System - Engine Mechanical System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Intake Manifold Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Engine Mechanical System / Intake And Exhaust System / Intake Manifold Repair procedures

Removal and Installation
1.
Disconnect the negative terminal (A) from the battery.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

2.
Remove the engine room cover (A), engine cover (B) and radiator grill upper cover (C).

3.
Remove the air cleaner assembly.
(1)
Remove the air duct (A).
(2)
Disconnect the breather hose (B).
(3)
Loosen the clamp (C) and then, disconnect the air intake hose from the throttle body.
Tightening torque :
2.9 ~ 4.9N.m (0.3 ~ 0.5kgf.m, 2.2 ~ 3.6lb-ft)
(4)
Remove the chamber air cleaner (D) and air cleaner assembly (E).
Tightening torque
Air cleaner assembly bolts:
7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

4.
Remove the fuel hose (A), the purge control solenoid valve (PCSV) hose (B) and the brake booster vacuum hose (C).

5.
Disconnect the ETC module connector (A), PCSV connector (B) and the PCV hose (C).

6.
Disconnect the MAP sensor connect (A) located at the rear side of intake module.

7.
Remove the wiring harness protector bolts, mounted on the intake module and the cylinder head cover.
Tightening torque :
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)
8.
Remove the high pressure fuel pipe bracket bolt (A), low pressure fuel tube bracket bolts (B) and the injector connector bracket bolt (C).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

9.
Remove the intake manifold module (A).
Tightening torque
1st step :
4.9 ~ 7.8N.m (0.5 ~ 0.8kgf.m, 3.6 ~ 5.8lb-ft)
2nd step :
19.6 ~ 26.5N.m (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

10.
Installation is reverse order of removal and tighten the manifold nuts with specified torque in the sequence shown.

    Intake Manifold Components and Components Location
    Components 1. Purge control solenoid valve (PCSV) and hose2. PCV hose3. ETC module4. Intake manifold module5. MAP sensor ...

    Exhaust Manifold Components and Components Location
    Components 1. Exhaust manifold heat protector2. Exhaust manifold3. Exhaust manifold gasket4. Exhaust manifold stay ...

    See also:

    ON/OFF Solenoid Valve Schematic Diagrams
    Circuit Diagram ...

    Hood Lift Repair procedures
    Replacement     • When removing and installing the hood lifter, an assistant is necessary. • When removing the clips, use a clip remover. 1. Using a screwdriver (A ...

    Components and Components Location
    Components Location 1. PCV Valve2. Canister3. Purge Control Solenoid Valve (PCSV)4. Fuel Tank Pressure Sensor (FTPS)5. Canister Close Valve (CCV)6. Fuel Level Sensor (FLS)7. Fuel Tank Air Filt ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com