>
Hyundai Equus Manuals

Hyundai Equus: Console Temperature Control Actuator Repair procedures - Heater - Heating, Ventilation and Air Conditioning - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Console Temperature Control Actuator Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Heating, Ventilation and Air Conditioning / Heater / Console Temperature Control Actuator Repair procedures

Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the console temperature control actuator connector.
3.
Verify that the console temperature control actuator operates to the defrost mode when connecting 12V to terminal 3 and grounding terminal 4.
Verify that the console actuator operates to the vent mode when connected in reverse.

1. -
2. -
3. Cool position
4. Warm position
5. Sensor ground
6. Feedback signal
7. Sensor (+ 5V)

4.
Connect the console actuator connector.
5.
Turn the ignition switch ON.
6.
Check the voltage between terminal 6 and 5.
Specification
Door position
Voltage (V) 
Error detecting
Cooling
3.8 ± 0.15
 Low voltage : 0.1V or less
Heating
1.2 ± 0.15
 High voltage : 4.9V or more

It will feedback the current position of the actuator to contorls.
7.
If the measured voltage is not within specification, substitute with a known-good console temperature control actuator and check for proper operation.
8.
Replace the console temperature control actuator if it is proved that there is a problem with it.
Replacement
[Console Temperature Control Actuator (A)]
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or remover, remove the driver's side crash pad side cover.

3.
After loosening the mounting screws, remove the crash pad lower panel (A).

4.
Disconnect the crash pad lower panel switch connector (A) and knee air bag connector (B).

5.
Remove the driver's side shower duct (A) after loosening the screw.

6.
Disconnect the connector (A) and then remove the console temperature control actuator (B) after loosening the mounting screws.

7.
Install in the reverse order of removal.
[Console Temperature Control Actuator]
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or remover, remove the driver's side crash pad side cover.

3.
After loosening the mounting screws, remove the crash pad lower panel (A).

4.
Disconnect the crash pad lower panel switch connector (A) and knee air bag connector (B).

5.
Remove the driver's side shower duct (A) after loosening the screw.

6.
Disconnect the console temperature control actuator connector (A), and then remove the temperature control actuator (B) after loosening the mounting screws.

7.
Install in the reverse order of removal.
    Mode Control Actuator Repair procedures
    Inspection 1. Turn the ignition switch OFF. 2. Disconnect the mode control actuator connector. 3. Verify that the mode control actuator operates to the defrost mode when connecting 12V to ...

    Auto Defogging Actuator Description and Operation
    Description The auto defogging sensor is installed on front window glass. The sensor judges and sends signal if moisture occurs to blow out wind for defogging. The air conditioner control modul ...

    See also:

    Rear cross traffic alert
    When your vehicle moves backwards from a parking position, the sensor detects approaching vehicles to the left or right side direction and gives information to the driver. Operating condition ...

    Fluid Components and Components Location
    Components Location 1. Oil injection hole2. Oil level check plug3. Oil drain piug ...

    Recalling Position into Memory
    1. Check that the shift lever is in P (Park) and the Engine Start/Stop Button is in the ON position. 2. Press the desired memory button (1 or 2). The system will beep once, then the driver's ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com