[Center Fascia Upper Panel]
| • |
Put on gloves to protect your hands. |
|
| • |
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related parts, to
prevent damage. |
| • |
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. |
| • |
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Using a screwdriver or remover, remove the cluster fascia upper panel (A). 
|
| 2. |
Using a screwdriver or remover, remove the center fascia upper panel (A). 
|
| 3. |
Disconnect the heater and A/C controller connector (A) and start connector (B). 
|
| 4. |
Loosen the mounting screws, remove the center fascia complete lower panel (A). 
|
| 5. |
Install in the reverse order of removal.
| • |
Make sure the connector is connected properly. |
| • |
Replace any damage clips. |
|
|
[Center Fascia Lower Panel]
| • |
Put on gloves to protect your hands. |
|
| • |
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related parts, to
prevent damage. |
| • |
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. |
| • |
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Remove the center fascia upper panel.
(Refer to Crash Pad - "Center Fascia Panel") |
| 2. |
Using a screwdriver or remover, remove the center fascia lower panel (A). 
|
| 3. |
Install in the reverse order of removal.
| • |
Make sure the connector is connected properly. |
| • |
Replace any damage clips. |
|
|
[Center Fascia Lower Tray]
| • |
Put on gloves to protect your hands. |
|
| • |
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related parts, to
prevent damage. |
| • |
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. |
| • |
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Remove the center fascia upper panel.
(Refer to Crash Pad - "Center Fascia Panel") |
| 2. |
Remove the center fascia lower panel.
(Refer to Crash Pad - "Center Fascia Panel") |
| 3. |
Remove the front console upper complete.
(Refer to Floor Console - "Floor Console Assembly") |
| 4. |
Remove the E-Shifter assembly.
(Refer to Automatic Transmission Control System - "E-Shifter") |
| 5. |
Loosen the mounting screws, remove the center fascia lower tray (A). 
|
| 6. |
Disconnect the lighting connector (A) and USB connector (B) and antenna (C). 
|
| 7. |
Install in the reverse order of removal.
| • |
Make sure the connector is connected properly. |
| • |
Replace any damage clips. |
|
|
Component Location
1. Center fascia upper panel2. Center fascia lower panel
...
Component Location
1. Crash pad lower panel
...
See also:
Front Pillar Trim Components and Components Location
Component Location
1. Front pillar trim
...
Trunk room lamp
The trunk room lamp comes on when the trunk is opened.
CAUTION
The trunk room lamp comes on as long as the trunk lid opens. To prevent unnecessary
charging system drain, close the trunk lid se ...
Pre-active Seat Belt (PSB) Repair procedures
Removal
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the safety belt (A) by turning it in the direction of arrow using a flat ...
Hyundai Equus: Center Fascia Panel Repair procedures
Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Body (Interior and Exterior) / Crash Pad / Center Fascia Panel Repair procedures
Center Fascia Panel Components and Components Location
Crash Pad Lower Panel Components and Components Location