>
Hyundai Equus Manuals

Hyundai Equus: Brake Booster Repair procedures - Brake System - Brake System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Brake Booster Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Brake System / Brake System / Brake Booster Repair procedures

Brake Booster Operating Test
For simple checking of the brake booster operation, carry out the following tests.
1.
Run the engine for one or two minutes, and then stop it. If the pedal depresses fully the first time but gradually becomes higher when depressed succeeding times, the booster is operating properly, if the pedal height remains unchanged, the booster is inoperative.

2.
With the engine stopped, step on the brake pedal several times.
Then step on the brake pedal and start the engine. If the pedal moves downward slightly, the booster is in good condition. If there is no change, the booster is inoperative.

3.
With the engine running, step on the brake pedal and then stop the engine.
Hold the pedal depressed for 30 seconds. If the pedal height does not change, the booster is in good condition, if the pedal rises, the booster is inoperative.
If the above three tests are okay, the booster performance can be determined as good.
Even if one of the above three tests is not okay, check the check valve, vacuum hose and booster for malfunction.

Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the cover.
3.
Disconnect the ECM connector (A) and TCM connector (B).

4.
Remove the ECM & TCM bracket installation bolts (C) and nut (D).
5.
Remove the fuel hose (E).

6.
Then take off the control harness and protector.
7.
Disconnect the vacuum hose (A) from the brake booster.

8.
Remove the master cylinder.
(Refer to Brake System - "Master Cylinder")
9.
Remove the snap pin (A) and clevis pin (B).

10.
Remove the mounting nuts.

11.
Remove the clevis (A).

12.
Remove the brake booster.

Inspection
1.
Inspect the check valve in the vacuum hose.
   
Do not remove the check valve from the vacuum hose.
2.
Check the boot for damage.
Installation
1.
Install the brake booster into the hole.
2.
Install the booster considering the length (A).
Between input rod end and clevis hole.
Standard length(A) : 23.2mm
Tightening torque(B) : 1.6 ~ 2.2 kgf.m

3.
Install the booster tightening nuts.
Tightening torque (B) :
16.7 ~ 22.6 N.m(1.7 ~ 2.3 kgf.m, 12.3 ~ 16.6 lb-ft)

4.
Install a snap pin (B) to the clevis pin (A).

5.
Set the gap (C) for stop lamp switch at 1.0 ~ 2.0mm.

   
1.
Before installing the pin, apply the grease to the clevis pin.
2.
Use a new snap pin whenever installing.
6.
Install the master cylinder, then install the brake tubes to the master cylinder.
(Refer to Brake System - "Master Cylinder")
7.
Connect the vacuum hose to the brake booster.
8.
Connect the fuel hose and control harness.
9.
Connect the connector after installing the ECM and TCM.
10.
After filling the brake reservoir with brake fluid, bleed the system.
(Refer to Brake System - "Brake System Bleeding")
11.
Check for fluid leakage.
12.
Check and adjust the brake pedal for proper operation.
    Brake Booster Components and Components Location
    Components 1. Brake booster2. Master cylinder assembly3. Washer4. Nut5. Vacuum hose (Lammda)6. Vacuum hose (Tau) ...

    Master Cylinder Components and Components Location
    Components 1. Reservoir cap2. Reservoir3. Grommet4. Cylinder pin5. Retainer6. Primary piston assembly7. Secondary piston assembly8. Master cylinder body ...

    See also:

    Knock Sensor (KS) Specifications
    Specification ItemSpecificationCapacitance (pF)950 ~ 1,350 ...

    Schematic Diagrams
    Circuit Diagram (1) Circuit Diagram (2) ...

    Rear Curtain Repair procedures
    Inspection Connect the battery voltage and check the rear curtain motor rotation. If the motor does not operate properly, substitute with a known-good rear curtain motor and check for proper op ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com