>
Hyundai Equus Manuals

Hyundai Equus: Master Cylinder Repair procedures - Brake System - Brake System - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Master Cylinder Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Brake System / Brake System / Master Cylinder Repair procedures

Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the cover.
3.
Disconnect the ECM connector (A) and TCM connector (B). And then take the protector of control harness off.

4.
Remove the ECM & TCM bracket installation bolts (C) and nut (D).
5.
Disconnect the brake fluid level switch connector (A) from the reservoir.

6.
Remove the brake fluid from the master cylinder reservoir with a syringe.
   
•
Do not spill brake fluid on the vehicle, it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.
7.
Disconnect the brake tube (B) from the master cylinder by loosening the tube flare nut.
Tightening torque :
18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m , 13.7 ~ 16.7 lb-ft)

8.
Remove the master cylinder (B) from the brake booster after loosening the mounting nuts (C).
Tightening torque :
12.7 ~ 16.7 N.m (1.3 ~ 1.7 kgf.m, 9.4 ~ 12.3 lb-ft)

Disassembly
1.
Remove the reservoir cap and drain the brake fluid into a suitable container.
2.
Remove the reservoir (C) from the master cylinder (B), after remove mounting screw (A).

3.
Remove the retainer ring (A) by using the snap ring pliers.
4.
Remove the primary piston assembly (B).
5.
Remove the pin (D) with the secondary piston (C) pushed completely using a screwdriver. Remove the secondary piston assembly (C).

   
Do not disassemble the primary and secondary piston assembly.
Inspection
1.
Check the master cylinder bore for rust or scratching.
2.
Check the master cylinder for wear or damage. If necessary, clean or replace the cylinder.
   
•
If the cylinder bore is damaged, replace the master cylinder assembly.
•
Wash the contaminated parts in alcohol.
Reassembly
1.
Apply genuine brake fluid to the rubber parts of the cylinder kit and grommets.
2.
Carefully insert the springs and pistons in the proper direction.
3.
Press the secondary piston (C) with a screwdriver and install the cylinder pin (D).

4.
Install the retainer ring (A) after installing primary piston assembly (B).
5.
Mount two grommets (D).

6.
Install the reservoir (C) on the cylinder (B), and then install the mounting screw (A).
Installation
1.
Installation is the reverse of removal.
2.
After installation, bleed the brake system.
(Refer to Brake System - "Brake System Bleeding")
    Master Cylinder Components and Components Location
    Components 1. Reservoir cap2. Reservoir3. Grommet4. Cylinder pin5. Retainer6. Primary piston assembly7. Secondary piston assembly8. Master cylinder body ...

    Brake Line Components and Components Location
    Components ...

    See also:

    Snowy or icy conditions
    To drive your vehicle in deep snow, it may be necessary to use snow tires or to install tire chains on your tires. If snow tires are needed, it is necessary to select tires equivalent in size and ...

    Front Seat Belt Pretensioner Repair procedures
    Replacement     • When installing the belt, make sure not to damage the pretensioner. 1. Remove the safety belt (A) by turning it in the direction of arrow using a fla ...

    Power Steering Motor Repair procedures
    Replacement 1. Remove the air cleaner (A). 2. Loosen the nut and then remove the air filter (A). 3. Remove the front bumper. (Refer to Body - "Front Bumper") 4. Remove the left head l ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com