>
Hyundai Equus Manuals

Hyundai Equus: Pre-active Seat Belt (PSB) Repair procedures - Seat Belt Pretensioner - Restraint - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Pre-active Seat Belt (PSB) Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Restraint / Seat Belt Pretensioner / Pre-active Seat Belt (PSB) Repair procedures

Removal
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the safety belt (A) by turning it in the direction of arrow using a flat-head screwdriver.

3.
Remove the center pillar lower trim.
(Refer to Body - "Center Pillar Trim")
4.
Remove the center pillar upper trim.
(Refer to Body - "Center Pillar Trim")
5.
After loosening the mounting bolt, then remove the front seat belt lower anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

6.
Loosen the front seat belt webbing guide (A) mounting bolts.

7.
After disconnecting the pretensioner connector lock pin, remove the front seat belt pretensioner connectors (A), loosen the mounting bolts, then remove the front seat belt pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

Installation
1.
Turn the ignition switch OFF.
2.
Disconnect the battery negative cable and wait for at least three minutes.
3.
Install in the reverse order of removal.
4.
Reconnect the battery negative cable.
5.
After installing the seat belt pretensioner, confirm proper system operation:
Turn the ignition switch ON; the SRS indicator light should turn on for about six seconds and then go off.
PSB Variant Coding
When replacing a PSB of the driver’s or passenger’s seat with a new one, be sure to carry out the Variant Coding procedure using GDS. (Only for vehicles without SCC)
   
PSB variants are coded for vehicles equipped with SCC. Therefore, Variant Coding should be performed only for vehicles without SCC.
PSB Variant Coding
1.
Turn the ignition switch OFF.
2.
Connect the GDS.
3.
Turn the ignition switch ON without the engine running.
4.
Select "PSB-LH" or "PSB-RH", and then select "PSB Variant Coding".

5.
Follow the instructions on the screen, and then press the "OK" button.

6.
Click "C1" if the vehicle is sedan type.
Click "C2" if the vehicle is limousine type.

7.
Click "C1" for vehicles with LDWS.
Click "C2" for vehicles without LDWS.

8.
Select the "OK" button after the "Complete" message has appeared.

    Pre-active Seat Belt (PSB) Schematic Diagrams
    Circuit Diagram ...

    Brake System
    ...

    See also:

    Memory Power Seat Unit (IMS & PSM) Repair procedures
    Removal 1. Remove the negative(-) battery terminal. 2. Remove the seats in the car. (Refer to Body - "Front Seat Assembly") 3. Remove the IMS & PSM module (A) after loosening 4 screws ...

    Transmission Control Module (TCM) Repair procedures
    Inspection TCM Problem Inspection Procedure 1. TEST TCM GROUND CIRCUIT: Measure resistance between TCM and chassis ground using the backside of TCM harness connector as TCM side check poin ...

    Vehicle identification number (VIN)
    The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. The number is punched on the floor under the front ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com