Hyundai Equus: Rear Glass Defogger Printed Heater Repair procedures
Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Body Electrical System / Rear Window Defogger / Rear Glass Defogger Printed Heater Repair procedures
Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Body Electrical System / Rear Window Defogger / Rear Glass Defogger Printed Heater Repair procedures
| Inspection |
Wrap tin foil around the end of the voltmeter test lead to
prevent damaging the heater line. Apply finger pressure on the tin foil,
moving the tin foil along the grid line to check for open circuits. |
| 1. |
Turn on the defogger switch and use a voltmeter to measure
the voltage of each heater line at the glass center point. If a voltage
of approximately 6V is indicated by the voltmeter, the heater line of
the rear window is considered satisfactory.
|
| 2. |
If a heater line is burned out between the center point and (+) terminal, the voltmeter will indicate 12V.
|
| 3. |
If a heater line is burned out between the center point and (-) terminal, the voltmeter will indicate 0V.
|
| 4. |
To check for open circuits, slowly move the test lead in the
direction that the open circuit seems to exist. Try to find a point
where a voltage is generated or changes to 0V. The point where the
voltage has changed is the open-circuit point.
|
| 5. |
Use an ohmmeter to measure the resistance of each heater line
between a terminal and the center of a grid line, and between the same
terminal and the center of one adjacent heater line. The section with a
broken heater line will have a resistance twice as that in other
sections. In the affected section, move the test lead to a position
where the resistance sharply changes.
|
Repair Of Broken Heater Line
Prepare the following items:
| 1. |
Conductive paint. |
| 2. |
Paint thinner. |
| 3. |
Masking tape. |
| 4. |
Silicone remover. |
| 5. |
Using a thin brush:
Wipe the glass adjacent to the broken heater line, clean with
silicone remover and attach the masking tape as shown. Shake the
conductive paint container well, and apply three coats with a brush at
intervals of about 15 minutes apart. Remove the tape and allow
sufficient time for drying before applying power. For a better finish,
scrape away excess deposits with a knife after the paint has completely
dried. (Allow 24 hours).
|
Components and Components Location
Component Location
1. Engine room relay box (Rear glass defogger)2. Rear window defogger switch (A/C controller)3. Rear window defogger4. Body control unit
...
Rear Glass Defogger Switch Repair procedures
Removal
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or plastic panel remover, remove the cluster fascia upper panel (A).
3.
Using a screwdriver or plastic panel ...
See also:
Rear curtain
To raise the rear curtain, depress the button. To lower the rear curtain, depress
the button again.
The rear curtain will be lowered automatically when you shift the shift lever
into R (Rever ...
Aux, USB and iPod® port
If your vehicle has an aux and/or USB(universal serial bus) port or iPod® port,
you can use an aux port to connect audio devices and a USB port to plug in a USB,
and an iPod® port to plug in ...
Luggage net (holder)
To keep items from shifting in the cargo area, you can use the holders located
in the cargo area to attach the luggage net.
CAUTION
To prevent damage to the goods or the vehicle, care should b ...
Categories
Hyundai Equus Manuals
© 2011-2026 Copyright www.heqmanual.com