>
Hyundai Equus Manuals

Hyundai Equus: Roof Trim Assembly Repair procedures - Roof Trim - Body (Interior and Exterior) - Hyundai Equus VI 2009-2026 Service ManualHyundai Equus: Roof Trim Assembly Repair procedures

Second generation VI (2009–2026) / Hyundai Equus VI 2009-2026 Service Manual / Body (Interior and Exterior) / Roof Trim / Roof Trim Assembly Repair procedures

Replacement
   
•
Put on gloves to protect your hands.
   
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the front seat.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the rear seat.
(Refer to Rear Seat - "Rear Seat Assembly")
3.
Remove the front pillar trim.
(Refer to Interior Trim - "Front Pillar Trim")
4.
Remove the canter pillar upper trim.
(Refer to Interior Trim - "Center Pillar Trim")
5.
Remove the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
6.
Remove the sub sunvisor.
(Refer to Roof Trim - "Sunvisor")
7.
Remove the sunvisor and retainer.
(Refer to Roof Trim - "Sunvisor")
8.
Remove the assist handle.
(Refer to Roof Trim - "Assist Handle")
9.
Remove the overhead console lamp.
(Refer to Body Electrical System - "Overhead Console Lamp")
10.
Remove the room lamp.
(Refer to Body Electrical System - "Room Lamp")
11.
Remove the rear window glass.
(Refer to "Rear Window Glass")
12.
Remove the hands free mic.
(Refer to Body Electrical System - "Hands Free Mic")
13.
Using a screwdriver or remover, remove the inside rear view mirror cover (A).

14.
Disconnect the inside rear view mirror connector (A), auto defog sensor connector (B), lane departure warning system (LDWS) connector (C), rain sensor connector (D).

15.
Remove the handsfree mike (A) and lamp (B) by pushing down the hook using a screwdriver.

16.
Disconnect the roof trim main connectors (A) and the mounting clips in the front pillar.
[Driver's]

[Passenger's]

17.
Disconnect the connectors (A) and the mounting clips in the rear pillar.
[LH]

[RH]

18.
Using a clip remover, detach the roof trim assembly mounting clips.
19.
Pull back the roof trim assembly (A) through the place where the rear window glass was removed.
   
•
Take care not to damage the roof trim when removing.
[Sadan]

[Limousine]

20.
Remove roof trim wiring harness (A) from the roof trim (B).
   
•
Take care not to damage the roof trim wiring harness (A) when removing.

   
1.
Apply the hot melt continuously when installing the roof trim wiring harness (A) on the roof trim (B) using the hot melt gun tool.
2.
Put anti-noise pad (C) on roof trim (B) to prevent the noise.
21.
Install in the reverse order of removal.
   
•
Make sure the connector is plugged in properly.
•
Replace any damaged clips.
    Roof Trim Assembly Components and Components Location
    Component Location 1. Roof Trim Assembly ...

    Interior Trim
    ...

    See also:

    Curtain Airbag (CAB) Module Components and Components Location
    Components ...

    Front Seat Back Cover Repair procedures
    Replacement     • Put on gloves to protect your hands.     • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply p ...

    Turn signals and lane change signals
    The ignition switch must be on for the turn signals to function. To turn on the turn signals, move the lever up or down (A). Green arrow indicators on the instrument panel indicate which turn ...

    Categories

    Hyundai Equus Manuals

    © 2011-2026 Copyright www.heqmanual.com